Trending Automotive Performance Engine Lifters Products

What is Automotive Performance Engine Lifters?


Top Customer Reviews: Ford Racing ...

Rating: 5 out of 5 with 2 ratings
5 / 5
The cost has verified This better to be have the $ 15000 work of part without capacity to transfer rotational motions partorisca take any gone...
5 / 5
This better be have the $ 15000 work of part without capacity to transfer rotational motions partorisca take any gone...

Top Customer Reviews: Air Lift 57138 ...

Rating: 4 out of 5 with 10 ratings
5 / 5
The box adds. Mina returned 96 E350 RV frame perfectly. Date partorisca walk restored the original, roughly 2' HIGHLY recommend. It was the little leary in a capacity to create on the 12K lb classifies C motorhome frame, but has done adds. The returns of boxes astonishingly well. A 2 now installs probably would be corrected partorisca the NASCAR crew of hole and promote it, but has taken longer in mine go for me. In general the product adds!
5 / 5
Was useless partorisca me. 1. Not even to to a same part likes them the cast. 2. All the parts have come free in of the boxes, not packing at all. 3. Any instruction or cast of parts. 4. Two of some stock exchanges of parts were opened.
5 / 5
Exactly like a box of the old impulse blown that it was in mine rv. It had installed the, tho. Too old to this I.
5 / 5
A must has partorisca older or basically any Vehicle, installed in 02 Ford E250 van..... wow That the difference. I produce add thank you.
5 / 5
My husband installed the he, and of then is mechanically bent, will not say it was easy, but some results were instantaneous! We tow Our 24' trailer with the car of race of full measure, 4-wheeler, box of tool, air comperessor, etc. And one camps the level remained and a walk was utmost, any bouncy like this first. I add compraventa, a lot happy with a product like this far!
4 / 5
This was quite easy to install in 1988 E350 motorhome conversion. It has taken roughly 4 hours for two men to install. Like this far I law adds, and does not have any complaint. My motorhome the chairs level now, and a walk is much smoother with roughly 75 lbs of air.
5 / 5
Installs has not been easy on class c but value each penny!!!
4 / 5
Any hard to install and totally changes a walk of one camps!!
Has created to A rear end likes any inferior is gone in each go and does not swing during a place when I drive!!
Not DRILLING!!!
Mina 3rd near !! Would have the c-class without them!!
5 / 5
The Photo does not correspond
To the models of pieces
5 / 5
An airlift 57138 was one wrong some partorisca my truck. They have not declared that the trucks have been used partorisca or that years.

Top Customer Reviews: COMP Cams 813-16 ...

Rating: 4 out of 5 with 1 ratings
4 / 5
So only that has required in the Prize adds & has shipped súper fast!

Top Customer Reviews: COMP Cams 2900-1 ...

Rating: 4 out of 5 with 2 ratings
5 / 5
The product has possessed anteriorly once take it. But I have taken they cleaned it to them up. They have not been used, but has had to still spent some time in the,. They are not in that cual expected the to be so something would buy directly of comp cams they. Good product, and fast nave. Purchase again.
4 / 5
It produces possessed previously took it once. But I took him it clean it up. They have not been used, but has has had to that still spent some time in his,. They are not partorisca like that expect partorisca be like this something would buy directly of comp cam they. Good product, and fast nave. Shopping again.

Top Customer Reviews: COMP Cams 800-16 ...

Rating: 4 out of 5 with 1 ratings
4 / 5
It has had always good regime with Competition Cam produced so it remains with them

Top Customer Reviews: COMP Cams 5003 ...

Rating: 4 out of 5 with 2 ratings
5 / 5
The element is so described in Info. It IS the good piece , solid of squad.

Has discovered while it uses it that the test uses a cape to pull a tool through a lifter the hammer is almost impossible. I have had of the hammer and the longitude 1/2' extension for the ratchet to touch he by a backside for the mark. Desprs He bottomed was was easy to touch a T cape for the fall (the pvot of cutting cover to leave easy scrolling and to prevents double mark).
Was able to mark all a lifter hammer with a crank and the still installed canes. It defies to Have to way that had to re-shows a crank to clear a crank balancers but is possible to do.
4 / 5
The element is described like this in Info. It is the good piece , solid of crew.

Has while discovered uses it that that looks for to use a boss partorisca pull a tool by means of a lifter bores is almost impossible. I have had to use the hammer & the longitude 1/2' extension for the ratchet to touch he for a backside for the value. With which he bottomed was was easy to touch a T boss for the emission (the pívot of cutting leaf to leave easy scrolling and to prevent the pair that validates).
Was able to value all a lifter bores with a crank and the still installed canes. Challenge to Have to that way that has had to that king-shows a crank to clear a crank balancers but is possible to do.

Top Customer Reviews: COMP Cams 813-1 ...

Rating: 4 out of 5 with 2 ratings
5 / 5
I have bought this so that I have required to measure for pushrod period in the SBC with the hydraulic fund tappet cam (Comp 12-210-2/268H). I have imagined a pushrod depth of chair for hydraulic and mechanical lifters of Comp would be a same. They are not , as you are buying this for a same reason while I have done... Not going to do! These have the chair the deep plus and will not give you an accurate measure.
3 / 5
I have bought this because I have required partorisca measure for pushrod period in the SBC with the hydraulic paving tappet cam (Comp 12-210-2/268H). I have imagined a pushrod depth of chair partorisca hydraulic and maquinal lifters of Comp would be one same. They are not , as you are buying this partorisca a same reason to the equal that have done... Not going partorisca do! These have the chair the deep plus and will not give you an attentive measure.

Top Customer Reviews: Crane 36530-16 ...

Rating: 5 out of 5 with 1 ratings
5 / 5
One of a lifters would not send oil up by means of cane of push. It takes defective lifter and expósito that the hole had not been drilled in a side of an inner piston. Experience he 3/32 Carbide Bit and trace lifter in my table of mill and hole drilled. Cleaned the thoroughly and reinstalled and has done.

After running engine so only down 100 miles and lifter in an opposite bank has begun partorisca do the strong tacking noise. I rechecked all a pedestal traces rockers partorisca pertinent adjustment and has determined that the lifter has failed.

Am sending behind partorisca the repayment and will purchase the different mark. Crane has used partorisca be the product adds but like all other products lately, the quality and the control of quality has diminished severely.


Related YouTube Video: