10 Best Steering Wheel Pullers -

Top Customer Reviews

Top Customer Reviews: Thorstone 46pcs ...

Rating: 5 out of 5 with 1 ratings
5 / 5
Fact very partorisca pull the steering wheel. Some measures of rays have required has been missing but found the in the tent of local hardware. In general the good box partorisca a prize

Top Customer Reviews: Shankly Flywheel ...

Rating: 4 out of 5 with 52 ratings
5 / 5
The cost has verified This neighbour is decently the fact and a box is well. Especially considering a price was very reasonable. Unfortunately, a selection of ray could be comprise the pair more options and some of one of concealed them is comprised so only have two rays in place of three. In some applications this is not the question but in some is. Unfortunately, a lot it dips this, but only shankley. The desire there is the little more line although cries a price slightly. Still, any bad in general.
4 / 5
The cost checked has Bought this partorisca pull a flywheel of mine 2011 yamaha grizzly the intentions were partorisca pull a flywheel all a way was partorisca take to a canal partorisca time sprocket of more easily take a canal on but roughly halfway by means of the attractive was there are them remarked a hub the piece in a box has begun to bend extremely to a point where the no longer felt sure using a could do adds in automotive applications but does not resist on well for powersports where all is returned more than tight
4 / 5
The cost verified has used this partorisca the way to project besides his use feigned and was the success. I used it partorisca pull the rear wheel of the 1964 murray tractive of gram. A tool bent but has taken a wheel was! With a lot of gross force,a hammer of air, and a lot of WD40. They are very pleased with this puller!!!
5 / 5
The cost has verified has a lot axial pullers partorisca ours ease of investigation.
But has then required to pull this geartooth goes. I have bought this box and a measure of the ray in fact is returned our wheel like any included has to that use the external ray of this container. It is very complete for him.

The appeal was amiably.
4 / 5
The cost checked has Purchased partorisca take a pulley of crank in the Nissan engine. A box is organised well. This in spite of, in spite of the good selection, one 6 X 75MM rays have required partorisca a work is not comprised in this box. A flange (slotted asks) will bend torsion weighed down - especially if a lip is facing outward.
4 / 5
The cost has checked the only question has run to has been pulled flywheel of engine partorisca bounce and has required three rays and there was so only two of this measure. Found another the taken a do one this in spite of. Any has not had the ray that loses a box has come so only with two. Another that that will maintain it cuz can require he in a future.
4 / 5
Works partorisca Purchase checked well partorisca pull a pulley of crank in mine 98 Chevy S10. A box has stirs it of different sized rays like this enough has to that return more cars there. The value adds for a price
4 / 5
The cost checked has Used partorisca take the flywheel partorisca '00 Toyota Avalon, with 200,000 miles, perhaps fro these people that has had a subject with a tool has used a wrong side of a dish, need to situate a flat side that the faces was like this some rays seat tight and equally in a dish and a big ray ready partorisca seat in a centre of a crankshaft, wrench of impact and WHAM!! Among any time.
5 / 5
The edges of Compraventas has checked undressed out of a piece of first time to centre used that. I have had a ray all a way thru before it take some . It is fact of the aluminium has launched. Economic Chinese junk.
5 / 5
The cost has checked is very partorisca one the majority of part. But taking of mine harmonic balancer. A ray of centre has begun takes partorisca undress. As it is not a more buy but still works.

Top Customer Reviews: POLARIS RZR ...

Rating: 4 out of 5 with 11 ratings
3 / 5
This has not done so sold by mine 2019 RZR XP Turbo. One (2)M5 the rays were too down. It was able to do this work to buy 2 longer M5 x 40 cape of rays of socket of covers. It IS the piece of the quality only does not do so sold for my model. I can not speak for other models.
5 / 5
I do not want to leave the bad description he in case that orders a wrong the element but this have not done for our 2015 RZR
5 / 5
This has not done like this sold partorisca mine 2019 RZR XP Disturb. One (2)M5 the rays were too many courts. It was able to do this work partorisca buy 2 more along M5 x 40 boss of rays of socket of discharges. It is the piece of the quality so only does not do like this sold partorisca my model. I can not speak by other models.
5 / 5
Simple tool,good construction, the fact adds in 2018 RZR XP 1000.
5 / 5
Súper Easy to use and the fact adds! Used in 2016 XP Disturb
5 / 5
has Struggled my steering wheel in the each one that way, has tried 3 different steering wheeler pullers that would not return , drum of brake pullers and everything goes in. Had my steering wheel is gone in 30 seconds once this is to arrive.
5 / 5
Does not want to leave the bad description in chance orders a wrong element but this have not done for our 2015 RZR
4 / 5
Utmost works partorisca take of Polaris volador stock
5 / 5
has Done likes field! Had my RZR 1000 steering wheel of inside minutes.
4 / 5
Right tool partorisca take voladora, a correct way.

Top Customer Reviews: 648748 Mstr ...

Rating: 4 out of 5 with 19 ratings
3 / 5
Work. The instructions are dark and confuse. Since it pull to 1955 wheel has used 4 parts. If it takes this proportionate : some instructions want to you to choose the set of rays of an upper row that access in two holes of ray in a wheel. A 'H' shaped separates then down access the, when is in place screwed in some holes in your wheel. An axis of long black in a left wing lower, then rays in a centre of a 'H' form (takes one covers plastic in an axial to find a pointed end).

Bandage a low axis in a a-wheeled centre and 'pop' the era comes your wheel.

Does not have any idea what each one 'Or' shaped the subject is enough in some instructions or that achieves....
5 / 5
This has done to pull the very old wheel effortless. Any muss, any fuss, only easy work with the very built tool joint.
5 / 5
I am like the plot of the train marries based the leaders in that has bought the number of 'pullers' some years. I have decided even so in 'invert' in the unit of the main quality this time and I very satisfied with this tool. Steel of big note, excellent machining and the durable spends case to maintain it each what together. I recommend it highly.
2 / 5
This element will do a work but alas perhaps only once. A quality of steel is poor and the nuts are was. Announced like EUA but produced of China. In general he a work.
5 / 5
The prize adds. Better products there but for one can of the prize did not beat it
4 / 5
I actuate Only the used the time that so far in an old ford hiboy but do an easy work and research to be abundance stout to use on and on.
5 / 5
It take the box has used, an interior of tools was greasy and has used. An element was angled the small bit. Traces to use everywhere!
5 / 5
Work. The instructions are dark and confusing. Of then it pull to 1955 wheel has used 4 parts. If taken this resupplied : some instructions want to you partorisca choose the together of rays of an upper row that access in two holes of ray in a steering wheel. A 'H' shaped separates then his low returns, when they are in planting screwed to some holes in your wheel. A black axial longitude in a lower left, then fulmine in a centre of a 'H' form (takes one covers plastic in an axial to find a pointed end).

Scrapes An axial down to a centre of a wheel and 'pop' was comes your wheel.

Does not have any idea that all one 'Or' shaped the subject is roughly in some instructions or that achieves....
1 / 5
Has had to that rent the box so only like this a leading reason have required to take the steering wheel in the GM transports. I do not go to rent this again!
4 / 5
Are like the plot to coach based in marrying the bosses in this I have bought the number of 'pullers' on some years. I have decided this in spite of to 'invest' in the unit of the main quality this time and I very satisfied with this tool. Steel of big note, excellent machining and the durable spending chance to maintain it all near. I recommend it highly.

Top Customer Reviews: OEMTOOLS 27017 ...

Rating: 4 out of 5 with 46 ratings
5 / 5
Measure: 1 Bandage A process the order was very easy and the product arrived in the timely way. It is very simple to use take and reattaching a steering wheel of my car of vintage.
5 / 5
Measure: 1 Band Looks for a prize can not complain, and work with the wide variety of vehicle is! It has taken less than 2mins partorisca take my steering wheel was! The only negative thing is when I ordered it, has said recieve for Thursday, and did not take it box Friday!
5 / 5
Measure: 1 Easy Band partorisca use, compact storage in a rugged plastic chance.
5 / 5
Measure: 1 Works of the far better band that a tool of the speciality sold for speciality Dodge negotiate of Diesel, the one who hawk the $ 55 tools that does not act. If the transmission needs your cashier of fuel partorisca the diesel Dodge, calms the favour and buy this instead. You will require partorisca add metric rays to a together partorisca do it universal.
5 / 5
Measure: 1 Band has Done sum! Pulled a rusty volador out of 1987 Chevy r10 likes butter. It has pleased extremely.
5 / 5
Measure: 1 Band has done well in mine 2001 firebird
4 / 5
has measured: 1 Band To the equal that has described. Easy to use.
5 / 5
Measure: 1 Band C3 telescopic wheel .. Perfecto spend
5 / 5
Measure: 1 Tool of law of Band a lot on 1988 F 350. Used the diverse time, am pleased.
5 / 5
Measure: 1 Vendar has had the pair of this type pullers on some years, this one has done like this expected, an only drawback is that has the blunt end that butts against a steering irons, as it can have the tendency partorisca walk calm so that it is turning it, partorisca prevent this sure mark some rays have dipped to a steering wheel is in of the equal distances of a wheel and he would have to that do well.

Top Customer Reviews: WYNNsky 46 Pieces ...

Rating: 4 out of 5 with 9 ratings
4 / 5
I have bought this partorisca pull the flywheel out of the Mercury 7.5 HP outboard engine. A question has found was that a four pronged bolting the groups would not return the centres are died in an iron of walk. It was so only he has gone by one 1/4 of a thumb, using three 5/16 th 2' the rays has had to that go to buy. It was hesitant to pull a wheel was centre of an iron of walk out of fear of harm of edge to a flywheel. Had so only two longitude 3 1/2 thumb the threaded car 5/16 rays in a box, and taken three. I have been and it has bought another 3 1/2 thumb scrapes. After gathering a puller with 3 1/2 thumb rays, was far enough out of an axial to walk that an error in some groups has not been the big shot anymore and has done well. Ossia The tool of big quality , concealed seldom will be used, but there is not any a lot of options when precise a. It was the good cost for me.
4 / 5
Puller The ray and the yoke have broken a puller the ray stuck in an end of a yoke. Used today to take my pulley of axial of the crank and he didnt do a work there is pulled not even my iron of crank and has broken. Of the that Spent this touches the junk. The vendor is bondadoso enought to substitute my crank of boxes puller the communication and cure your needs.
Will recommend this vendor
Thank you again
5 / 5
has to Do fault his purpose when it takes a cam pulley of the 2006 Ford Merge 3.0. I have had to that buy my rays of ray suitable for maintaining fulmine in place. Work very this in spite of.
4 / 5
This together has had all and more than has required. It was able to take mine 79 fords voladora with a lot of little evert. I recommend this product.
5 / 5
Laws well. It likes that some clips of of boxes some rays in like this his whose falls was. Good prize and has shipped punctually
5 / 5
This returns our needs for our edges and work of maquinal amiably!
4 / 5
Laws a lot cheaply fact and flimsy but volume that paid for
5 / 5
has Done adds to take a steering wheel in my old truck. I have loved the box that could accustom take pulleys,etc in some futures also and this one comprises all required for that.
4 / 5
Still pull of a steering wheel, this is not an economic plus a, but am happy bought it reason have finalised to use 2 different period rays and a washers. Justo well for the have everything in there. It has done perfectly and fast and easy to use. I have it that has not used never one of this first and has not looked any video on regarding the use. It is so only that easy. Very simple and smooth.

Top Customer Reviews: Chrome Pin Puller ...

Rating: 4 out of 5 with 20 ratings
5 / 5
This fifth hook am adds. Strong,robust and a perfect measure to hang by behind my tank of fuel in my T 680 taxi in the daytime. I fall and hook quite 8 times the sometimes more day. A creation of a cape and a hook is perfect to take good advantage. My old puller has taken angled when tried to pull the cape of tandem of stubborn trailer. This one is quite strong to do a work without sprain.
5 / 5
That is to say a a flight ! The launched of dishes of armours any aluminium. The cape has turned a right road also like a hook of original milk! More or has had there the like this before until any one decides that they require more than you. Perfecto
5 / 5
I use it to pull tanks of propane of fuel of the engine (50lbs) and BBQ tanks (20lbs) of my truck. Lost my another like this so still buy it again.
5 / 5
I produce it adds for my husband a truck driver. Any one always takes chair. More abordable that a decree of truck
5 / 5
This was the prize adds for the element of quality. Any one something usually was has wanted by or has excited enough, honestly can say this was better concealed expected and has surpassed my expectations. Fast nave, also! If you are looking for the fifth wheel puller, would recommend easterly unit
5 / 5
This sum of records of the tool. It IS robust and marks exactly that has been designed to do. Coverage more soiled or greasy shirts for me. No longer I have to achieve among some tandems to pull an emission of pin of the king with my hand and apresamiento big or road of winter slush and muck of a fund of a trailer or wheel throughout me. The amazon and the prize adds has taken he in me faster this has said they
5 / 5
Excellent tool partorisca industry of communications. Quality very better and durability partorisca open communications Handholes that the typical elements have sold partorisca this purpose.
3 / 5
I work in a Dairy Department in ours perfectionist venue, and our hook of tins has broken. After taking a runaround of the our cashier of tins and my manager, looked on Amazon. This element is feigned partorisca something more, but the law adds like the hook of tins. Has the heavy boss and is a perfect period. It can manage pull a weight of 24 chevrons partorisca milk repeatedly. To good sure recommended.
4 / 5
This fifth hook are adds. Strong,sturdy and a perfect measure partorisca hang for behind my tank of fuel in mine T 680 taxi of day. I fall and hook roughly 8 times the day sometimes more. A creation of a boss and a hook are perfect to take good leverage. My old puller has taken bent when searches to pull the boss of tandem of stubborn trailer. This one is quite strong to do a work without bending.
5 / 5
Ossia A one master! Fact out of armour plate any aluminium. The boss has turned a right way also like a hook of original tins! One more had him there like this before until any one decides that they require more than you. Perfecto

Top Customer Reviews: Orion Motor Tech ...

Rating: 5 out of 5 with 1 ratings
5 / 5
Like this far it is been doing a work.
Has had to that buy 3 long rays. One 2 this is to go in a together 1/4 - 28 has not gone long enough for a task. A neighbour is of good quality.
Still has to that pull my steering wheel, will see like this goes.
Would buy this again!

Top Customer Reviews: GG Grand General ...

Rating: 4 out of 5 with 35 ratings
4 / 5
Measure: 33' trailers of circle of tractor of double trailer and are constantly hooking and unhooking trailers of trailers of tractor and dollies. My shoulders constantly cry in hurting to pull stubborn nail all a moment my dresses would be constantly dirty partorisca rub against some funds of some trailers. No more!

This pin puller is partorisca have to that very heavy and with an extra piece the very easy fact to unhook a jost dollies this has a mechanism partorisca close that it maintains a pin partorisca exit - the a lot of messy two rid unlock ossia usually the real ache.

Has had mine partorisca the week now is easily mine the majority of coveted tool in my truck! A very small prize partorisca pay so that he , so much have bought like this a partorisca the partner a lot well of the mine the one who a same thing.

Daría ten tin of stars !
5 / 5
Measure: 27' I have expected box I kings-there is wounded my first shoulder to buy this puller, no ready for my part. If you fall and the hook a lot is a lot of value of the money. Awesome Tool and maintains calm to take like this dirty of a trailer underside.
4 / 5
Measure: 33' Work like this has to that, is the lil heavy in a zone of boss that are add, the must has to that save your Measure
4 / 5
of shoulder: 27' works so only well.. It is so only to 5th it turns puller... Or taking that or attended... It likes tht of east an is not like this long.. A longitude some r the ache partorisca store
4 / 5
Measure: 27' Amur this attractive. So only long enough to take a work done. It has to that it weighed it enough so that it does not bend. A lot happy bought it.
5 / 5
Measure: 27' we have moved recently our @@subject to the warehouse with shipping doors and this little here helps of same gem with emotional ours flaps to jump when uploading and downloading trucks. The tool adds.
4 / 5
Measure: 33' My husband is the truck driver and has said this was the product adds . It is easy to use, sturdy and felt sure that it is work and would last the long time.
4 / 5
Measure: 24' this is the fifth wheel adds puller and also adds to pull straps and canals in mine flatbed
4 / 5
Measure: 33' A period is in his point for me and he the less uncomfortable fact the tote of my car trunk to a taxi of one 18-wheeler. Ossia The solid piece of compulsory crew for which want to maintain his shoulders sãos.
4 / 5
Measure: 33' Perfect cost for the seeds engine! Súper Handy and durable!

Top Customer Reviews: GEARWRENCH Steering ...

Rating: 4 out of 5 with 10 ratings
3 / 5
Has the 05 chevy Malibu and a flat tip is the ache to vary and stay to mark there
4 / 5
Used in the dealership occasionally for the GM technology without problems. Used mostly in Corvettes with a steering problem of lock of the column. Sometimes one beats of wheel that is very hard to exit.
5 / 5
That is to say the tool adds ... Taken 2 minutes to extract a cranshaft pulley to be able in car!
5 / 5
Perfect fact to pull and press in a harmonic balancer for mine 6.2l CUCV automotive of diesel. No the tool will use the plot but he are a right tool for a work.
5 / 5
If you possess the cart of mark of the the USA then this can do since you. Has had to the tend he of hardware and compraventa very time metric rays only to be able to use this thing. It is it impacted concealed does not have metric rays, perhaps KD the tools are not conscious of a fact that 99% of a world-wide changed in the mark of metric decades and that other manufacturers of stock of ship of the tool of metric rays.
2 / 5
Has the 05 chevy Malibu and a flat tip is the ache partorisca line on and rests to mark there
5 / 5
Used in the dealership occasionally for the GM technology without questions. Used mostly in Corvettes with a steering question of lock of the column. Sometimes a steering wheel can be a lot last to exit.
5 / 5
Ossia The tool adds ... It takes 2 minutes partorisca extract a cranshaft pulley partorisca be able to car!
4 / 5
Has done perfect to pull and push in a harmonic balancer partorisca my CUCV engine of diesel. No the tool will use the plot but he is a right tool partorisca a work.
5 / 5
He Possess the car of mark of the the USA then this can do for you. I have had to that go to the tent of hardware and buy fulmine metric long so only to be able to use this thing. I am impacted of not having to that the metric rays, perhaps KD the tools is not conscious of a fact that 99 of a world-wide changed to the metric decades does and that other costruttrici of stock of ship of the tool of metric rays.




Related YouTube Video: